Please go to this link to find the latest version https://www.nord-lock.com/services/manuals/expander/installation-instructions/stepped-pin-spanner-nut-secured/

Installation Instructions

Stepped Pin, Spanner Nut Secured

v4-2

Following these instructions will ensure that the Expander System is installed correctly and the pivot life is prolonged.

Congratulations! You have purchased a custom engineered solution to the pivot wear problem on your machine. Contact your dealer or Expander before proceeding if you have any questions.

 

1 Bolt. 2 Washer. 3 Sleeve. 4 Axle (Pin). 5 Securing spanner nut. 6 Threaded washer.

The picture shows a female axle but the principle is the same for other designs.

Preparation

1

Remove any bushings to eliminate future wear between the bushing and the mounting lug.

2

Repair any structural damage i.e. cracks or bent lug ears before installation.

3

Smooth out irregularities in the bore surfaces.

4

The difference between min and max diameter in the worn lugs must be within .06” (1.5 mm) for the sleeves to fit correctly.

ATTENTION! If the worn lugs diameter at any point is 2 mm (.080”) or more over original lug diameter contact your dealer or Expander System. You will need oversized sleeves. 

Installation

5

Grease the sleeves and axle with grease available, preferably graphite grease. Do not grease the threads!

NOTE! If applicable: position greasing outlet 90 degrees to force direction to minimize stress concentration at outlet.

 

6

The spacer is always positioned on the opposite side of the stepped part of the axle. If the pivot already has a spacer, leave it in its position. If the Expander System includes a spacer, place it between the inner sphere of the bearing and the lug ear, with the bevel facing the bearing.

 

7

Insert the axle. Install securing spanner nut and threaded washer on the side with small axle diameter. Position to achieve a gap between the threaded washer and the lug. Mount and tighten the fastener until the axial play is eliminated.

8

Install sleeve, washer and fastener on the side with large axle diameter. Tighten the fastener with recommended torque.

Remove fastener, securing spanner nut and threaded washer. Install sleeve. Reinstall securing spanner nut, threaded washer and fastener. Keep the securing spanner nut loose and tighten the fastener with recommended torque. Tighten the securing spanner nut.

Torque recommendations

9

Hex Bolts

Torques M12-M24 ± 10%, M30... +30/-0%

  M12 M14 M16 M20 M24 M30 M36 M42
Nm 70 115 175 350 500 600 700 900
lb-ft 52 85 129 258 369 443 516 664

Hex Nuts: Standard Height

Torques M12-M24 ± 10%, M30... +30/-0%

  M12 M14 M16 M20 M24 M30 M36 M42
Nm 65 115 175 250 350 500 600 700
lb-ft 48 85 129 184 258 369 443 516

Hex Nuts: Low Height

All Torques ± 10%

  M12 - M16 M20 M24 M30 - -
Nm 60 - 125 200 275 350 - -
lb-ft 44 - 92 148 203 258 - -

Spanner Nuts

All Torques ± 10%

  M17 M25 M35 M45 M55 M65 M75 M85
Nm 50 120 250 500 600 700 800 900
lb-ft 37 89 184 369 443 516 590 664

Securing Spanner Nut

Max Torque

  ....M100 M100.... - - - - - -
Nm 50 80 - - - - - -
lb-ft 37 59 - - - - - -
10

After initial torque move machine through full range of motion several times. Loosen the securing spanner nut and recheck the torques. 

11

Ensure that there is a minimum distance of 0,5 mm (.02”) between the washer and the lug. ATTENTION! If the washer is in contact with the lug contact your dealer or Expander System.

 

Dismounting

12

Unscrew the fasteners on both sides. Remove securing spanner nut, threaded washer and washer. On the nonstepped end, tap the axle until the tension on the sleeves is released (use a piece of pipe between the axle and the mallet/hammer not to damage the threads).

13

Tap the axle alternatively on left and right side until the tension on the sleeves is released. Remove the sleeves and axle. Do not damage the threads.